Correct, installation of the MORryde Rubber Equalizers for Tandem Axle Trailers, # MR87ZR does not require replacement of the hangers or shackles if those components are properly sized and in good repair. You can reuse the existing hardware for installation. view full answer...
I have a few options for you to help with identifying the bearings on your trailer. The first and easiest method would be to crawl under the trailer and look for the axle tag on the beam. This should give an axle capacity which we can then use to find the bearings based off industry standards. For example, a 3,500 lb axle uses L68149 and L44649 bearings like what comes with the Hub Bearing Kit for Lippert, Dexter, and Al-Ko Axles part # BK2-100. The other option would be to take the hubs... view full answer...
I recommend LED Trailer Tail Light w/ Bracket - 4 Function - 22 Diodes - White Base part # 328-003-81LM1 for the driver's side and LED Trailer Tail Light - Stop, Turn, Tail - 22 Diodes - White Base part # 328-003-81M1 for the passenger side. These lights measure 8-11/16" wide and 3-7/8" tall so you want to compare them to your existing lights since I do not know the dimensions of your existing lights. If they are the same size or bigger (and you have the space) then your existing lights... view full answer...
As long as your 2015 Keystone Outback 316RL Trailer is equipped with 3" round axles (which would be typical for 5,200 pound units) the Roadmaster Comfort Ride Shock Absorbers # RM-2460 will work perfectly. This kit is designed for tandem axle trailers like yours, is compatible with your existing MorRyde system, and will absolutely help to smooth out the ride of your trailer during travel. This is going to provide a significant improvement in terms of side-to-side movement and bounce on... view full answer...
I believe you are asking for a replacement fireplace for the Greystone Wf2613. The exact replacement for the Wf2613 fireplace according to Greystone is Greystone 26" Electric Fireplace with Crystals - Recessed Mount part # 324-000069. view full answer...
Yes, the Adco SFS AquaShed Cover for Travel Trailer - Up to 34' Long - Gray # 290-52246 is designed to fit travel trailers that are 32' - 34' long so you won't have any issues using it with your 32' 2018 Keystone Outback Travel Trailer. Cinch ropes at the front and rear of the cover remove slack and reduce billowing while the weighted straps with buckles secure cover under vehicle and prevent the cover from blowing off in the wind. Zippered panes on the passenger's side offer easy access... view full answer...
If your trailer isn't prewired for a specific brand then you can easily use any brand of your choice. Typically Keystone prewires their trailers for Furrion camera systems so you'll want to take a look a the mount on the back of your trailer. If it is the shark fin design like I have pictured below or has Furrion written on it then you know which system you're prewired for.
If you have the prewiring in place you can quickly and easily plug in the Furrion Vision S Wireless RV Backup Camera... view full answer...
To get an exact replacement screen door latch for your 2019 Keystone Outback Travel Trailer you would need to reach out to the manufacturer directly to see if they could ship you a replacement. This is probably going to consume a large amount of time and no guarantee that you'll get what you need so I recommend just replacing the old latch with the Bi-Directional Screen Door Latch # 37206-11865 and making new holes. It doesn't have the extra prongs but will be more than stable with the... view full answer...
The MORryde Shock Absorbing Suspension Equalizers # MR87ZR are approximately 1-1/8" taller than the Curved Equalizer # TREQ104 when measured from the top bolt hole center to the center line off the lower bolt holes. This would raise the trailer height approximately 9/16". Do remember the rubber cushion used on this Equalizer does allow for the equalizer to travel up and down so at times the height could be slightly more or less depending on the weight and any road shock traveling through... view full answer...
Since the distance between the horizontal mounting holes on center of your current equalizers on your 2017 Keystone Outback is 5-1/2" and the MORryde Cre3000 equalizers that you purchased have are 6-1/2" you will either need to use shorter equalizers, or shorter shackle straps to keep your suspension geometry the same.
For shorter equalizers I recommend the Equa-Flex Cushioned Equalizers - Double Eye Springs - Tandem Axle - 3K to 6K # LC279687 which measure 5-1/2" between the horizontal... view full answer...
I am not sure what the spacing is on your 2020 keystone Outback 210 URS but the Road Armor Shock Absorbing Equalizer Kit - Tandem Axle item # LC696740 bolt spacing is 6 inches wide, 4 3/8 inches from the top bolt hole to the side holes, and from the top bolt hole to the bottom of the equalizer is 7 1/4" tall. I have attached a picture detailing the dimensions. If your equalizer's dimensions are different please email me what they are and I will be glad to find you the correct replacements. view full answer...
The only way to determine the correct kit for your 2016 Keystone Outback 255UBH would be to remove the hub/drum assembly and measure the spindle at points B (grease seal) and C & D (bearings) to get the inner diameter. Bearing kit # BK1-150 and kit # BK2-100 use different grease seals and inner bearings and there unfortunately isn't a guide available to tell me what spindle you have. view full answer...
I am happy to help you install the Curt Triflex part # C24VV in your 2019 Ford Expedition with a factory 7-way. I recommend to use Curt Custom Wiring Adapter for Trailer Brake Controllers part # C51436 to install the brake controller. It will plug into a built-in port under the dash of the Ford and the other end plugs into the brake controller to power the brake output circuit on the 7-way to tow a trailer with brakes. view full answer...
Assuming the 36 foot measurement you took was for the body of your Keystone Outback travel trailer (not including the tongue), we do have a superb option for winter weather that will fit your trailer:
- Adco Olefin HD All-Climate + Wind RV Cover for Travel Trailer # AD39ZR
The # AD39ZR fits trailers that are between 34'1" and 37' long, and is specifically designed to offer your trailer the best protection against all the elements it can face, including the snow and wind that you'll see... view full answer...
The Sew-In Snap Tape for RV Curtains part # 37281005 use a standard size snap fitting which is not called out specifically by the manufacturer. The most important thing is to be sure you get the correct connectors based on your track such as the Snap-In RV Curtain Carrier part # 37281075.
I have attached a full list of the connectors below as well. view full answer...
I reached out to my contact at Dexter and based on the serial number you provided your axle was made in October of 2008 and will use braking assemblies # 23-455 for the passenger side, and # 23-454 for the driver side.
I included videos of the products mentioned for you to take a look at. view full answer...
I have a few options for you to help with identifying the bearings on your trailer. The first and easiest method would be to crawl under the trailer and look for the axle tag on the beam. This should give an axle capacity which we can then use to find the bearings based off industry standards. For example, a 3,500 lb axle uses L68149 and L44649 bearings like what comes with the Hub Bearing Kit for Lippert, Dexter, and Al-Ko Axles part # BK2-100 or the Easy Grease Trailer Hub and Drum Assembly... view full answer...
From specs available to me online, the 2022 Keystone Outback 328RL Travel Trailer is 37.58 ft. (451 in.) in length as measured from back bumper to coupler. The Adco Olefin HD All-Climate + Wind RV Cover for Travel Trailer, # AD39ZR is a great fit for this travel trailer as it is overall 447" long x 106" wide x 102" tall. This will fit over the travel trailer and probably provide options of enclosing the propane tanks as well, pulling tight with included cinch ropes leaving the coupler... view full answer...
The Dexter Electric Trailer Brake Kit part # K23-462-463-00 is designed for 4,400 lb axles with a four bolt mounting flange. If this is what you have then it will work great. The axle capacity can be found on the axle tag sticker in the center of the beam. Unfortunately, we cannot look up parts for any one specific trailer. The kits is for two assemblies. view full answer...
Go To Results